Menu Close

Fireproofing vs Firestopping in NJ Commercial Buildings: Which Service Do You Need?

Here’s how it usually comes up. You’re fitting out a space in an office building in Freehold, or a warehouse in Wall. The electrician runs new conduit through a rated wall. The plumber cores a hole in the slab. Then an inspector walks through, looks at the gap around a pipe, and writes it up. Somebody on the job says, “get the fireproofing guy,” somebody else says, “no, that’s firestopping,” and now you’re not sure which one to call.

They’re two different jobs, and both are about passive fire protection. Fireproofing protects the building’s structure, mostly the steel beams and columns, so it doesn’t lose strength and fail during a fire. Firestopping seals the holes and gaps in fire-rated walls and floors, the openings around pipes, wires and ducts, so fire and smoke can’t slip from one space into the next. If the issue is bare structural steel, you need fireproofing. If the issue is a penetration or joint in a rated wall or floor, you need firestopping. On a lot of commercial jobs, you need both.

Fireproofing or Firestopping?

The quick difference

FireproofingFirestopping
What it protectsStructural steel: beams, columns, decksOpenings and joints in rated walls and floors
What it doesKeeps steel from heating up and weakeningStops fire and smoke passing through gaps
Common materialsSpray-applied fire-resistive material, intumescent coatingsFirestop sealants, collars, wraps, mortars
Typical testsUL 263 / ASTM E119ASTM E814 / UL 1479 for penetrations, UL 2079 for joints
When it usually comes upNew steel construction, renovations exposing steelAny time something is run through a rated wall or floor

What fireproofing does

Steel doesn’t burn, but it does get weaker as it heats up. Carboline, a fireproofing manufacturer, puts it plainly: the load-bearing capacity of steel drops as its core temperature rises. Fireproofing is insulation for the structure. It keeps the steel cool enough, for long enough, that the building stays standing while people get out and firefighters do their work.

There are two main types. Cementitious spray-applied fire-resistive material, usually just called SFRM, is mixed on site and sprayed on. It’s rough-looking, so it typically ends up hidden above a ceiling or behind a wall. Intumescent coatings go on thin, like paint, and swell into an insulating char when they get hot. Those are often used where the steel stays exposed and needs to look finished.

Commercial buildings in the U.S. generally need somewhere between a one- and three-hour fire-resistance rating, and fireproofing products are tested to standards like UL 263 and ASTM E119. The thickness that goes on the steel depends on the rating the design calls for.

What firestopping does

Firestopping deals with the holes. A fire-rated wall or floor only works if it’s continuous. Every time a pipe, cable bundle, or duct goes through it, there’s a gap, and that gap is a highway for fire and smoke unless it’s sealed with a tested system.

Penetration firestop systems are usually tested to ASTM E814 or UL 1479, and joint systems, like the gap at the top of a rated wall, to UL 2079. You’ll see ratings like an F-rating, which is how long the system keeps flames from passing through, and a T-rating, which is how long before the temperature on the far side rises 325°F. The point is that a firestop isn’t just caulk in a hole. It’s a specific tested system, installed the way that system was tested.

Why firestopping keeps coming back

Because buildings keep changing. Every tenant fit-out, every new data line, every HVAC change can punch a fresh hole in a rated wall. The International Fire Code, which New Jersey’s fire code is based on, puts this on the owner. It says the owner has to keep an inventory of required fire-resistance-rated construction, look it over every year, and repair anything that’s been damaged, altered, breached, or penetrated, with records of the inspections and repairs.

The Firestop Contractors International Association has a line about it that’s hard to argue with: simply covering a hole isn’t a repair. A breached firestop has to be fixed following the tested system’s listing and the manufacturer’s instructions.

So which do you need?

Bare or damaged steel on a structural member? That’s fireproofing. A pipe, conduit, cable tray, or duct going through a rated wall or floor, or a gap at the top of a rated wall? That’s firestopping. Renovating a space where both the steel and the rated assemblies get opened up? Probably both.

If you’re not sure, have someone walk the space and look before the ceiling goes back up. It’s much easier to fix while everything’s exposed.

Asking the right questions

Whoever you hire, ask what tested systems they’re installing and whether they’ll document them. For firestopping in particular, ask whether they’re approved under a third-party installer program like FM 4991 or UL’s Qualified Firestop Contractor Program. Those programs audit the contractor’s office and job sites every year. They aren’t required on every job, but some specs call for them.

Frequently asked questions

What is the difference between fireproofing and firestopping?

Fireproofing protects structural steel from heat so it doesn’t fail in a fire. Firestopping seals penetrations and joints in rated walls and floors so fire and smoke can’t pass through.

What is SFRM?

Spray-applied fire-resistive material. It’s a cementitious fireproofing sprayed onto structural steel, usually hidden behind ceilings or walls.

Who is responsible for maintaining firestopping?

Under the International Fire Code, the building owner keeps an inventory of required fire-rated construction, inspects it every year and repairs anything that’s been breached.

Can I just fill a hole in a rated wall with caulk?

No. A firestop has to be a tested system installed as listed. Covering a hole isn’t a repair.

Need fireproofing or firestopping on a commercial job in Central Jersey? DJG Insulation works out of Wall Township across Monmouth, Ocean and Middlesex Counties (NJ License #13VH10534300). Call 732-226-5344, see our Fireproofing, Firestopping, and Commercial services, look through our Gallery and Testimonials, browse all our Insulation Services, or contact us.

Related Posts